Magnum Force Stage 2 Cold Air Intake System
BMW 2006-2008 E60 M5
E63/E64 M6 V10-5.0L #54-11272
Airflow and volumetric efficiency means huge high-flow, conical air filters are the first
step to increase airflow to the engine. Steel heat shields and molded plastic air tubes
keep hot air out and fresh, cold air flowing to the filter. Velocity stacks and precision
designed intake tubes provide smooth, uninterrupted airflow to the throttle body.
28 HP Max Gain @ 5879 RPM
24 Ft-lbs of Torque Max gain @ 5879 RPM
117% Increase in CFM!
Large washable/reusable conical air filters for increased air flow and better performance
NO DRILLING REQUIRED! Durable 16 gauge powder coated housing uses existing mounting locations.
Powder-coated air filter housing blocks out engine heat and attenuates sound.
*MAS not included
MSRP - $743.75
Due to extreme popularity, please contact to check availability.
Free Shipping with Buy-it-Now!
Who is aFe?
Advanced Flow Engineering, Inc. (aFe) produces high flow, high performance air filters & intake systems for the automotive industry. Founded in April, 1999, aFe was created to address an obvious need in the automotive aftermarket industry: a lack of choice for a high performance aftermarket air filter.
Cold Air Equals More Power
In designing out the stock air box, aFe designs the largest air box that they can for each vehicle application. Even though they make it as large as possible, aFe is careful to use stock mounting points. There is no need to cut or drill anything when you install an aFe kits. The air box is made as large as possible so that the largest possible air filter can be used.
aFe's Magnum Force Stage 2 intakes systems:
Compared to our other systems, the Magnum FORCE Stage 2 intake system replaces the entire stock air induction system to the throttle body or turbo housing. Remembering aFe’s motto “Stock Sucks”, they eliminate the stock air box, the stock air filter and the stock intake tract. The only thing retained is the stock electronics. They make sure that the Stage 2 system like all of aFe’s intake systems works with the stock electronics
16-gauge powder-coated steel – Durable, OE look finish
Trim sealed or covered – Seals out hot engine air
Powder-coated covers on some applications
Secured PEM-nuts – Easier installation
Welded and preassembled sheet metal – Faster Installation
Pre-positioned opening for Stock attachments - No dangling wires, relocating hoses or tubes.
3-angle velocity stack adaptor on some applications
Tubes designed so that the factory MAF sensor is positioned in just the right place so that you get the best performance possible without triggering the CEL
aFe's Magnum Force Stage 1 intakes systems:
With the Magnum FORCE Stage 1 intake system, aFe replaces the stock air box and the stock air filter. By replacing the restrictive air box and air filter, there is a noticeable improvement in airflow and power. However, Stage 1 retains the stock intake tract.
In designing out the stock air box, aFe always tries to design in the largest air box that they can. When replacing the stock intake tube as they do in their Stage 2 systems, you have more flexibility since you can change the tube configuration. However adapting to the stock intake tube forces some limitation on the design. Even with adapting to the constraints of the stock intake tube, aFe is careful to use stock mounting points. There is no need to cut or drill anything when you install an aFe kit.
16-gauge powder-coated steel – Durable, OE look finish
Trim sealed or covered – Seals out hot engine air
Powder-coated covers on some applications
Secured PEM-nuts – Easier installation
Welded and preassembled sheet metal – Faster Installation
Pre-positioned opening for Stock attachments - No dangling wires, relocating hoses or tubes.
3-angle velocity stack adaptor on some applications
TECHNOLOGY
More Horsepower/Torque Medical grade cotton gauze filter media reduces air restriction and increases engine output. Surface area optimized to reduce pressure differential across the element resulting in reduced back pressure and increased torque
Increased Airflow Precision pleat geometry optimizes airflow through intake systemEngineered to control maximum filter face air velocity with deep precision pleats
Improved Engine Protection Multi-layer oiled cotton gauze attracts and traps contaminants without sacrificing air flow. Sturdy epoxy coated wire mesh construction protects filter media (and engine) from large debris
Poorly designed seals either permit air leakage or distort the filter housing. Many other filters use plastisol or air/foam seals. Over time, heat and chemical attack cause this material to lose its elastic characteristics, which result in seal failure. On the other hand, foam type seals simply cannot pass the test of time. Use of a foaming agent reduces the amount of polyurethane used in the part. Minimal heat exposure tends to turn this material into powder. The aFe air filter features a superior seal design with a 100% polyurethane material construction.
LIMITED LIFETIME WARRANTY
Limited Lifetime Warranty Cleanable and reusableUrethane seal outlasts conventional materials (especially under extreme engine temperatures). Longer Filter LifeThe last filter your vehicle will ever need
Please visit our e-Bay store and check out our other great accessories.
Products All products are new and in factory boxes unless otherwise stated.
Sales Tax Colorado State Residents will pay 3.7% Colorado State Sales Tax
Shipping Please allow 7-10 business days for shipping. Refer to auction description for shipping charges. Shipping to lower 48 states only, unless prior arrangements are made. Additional shipping charges apply to Alaska, Hawaii and Canada, please contact us for details. We will ship to Europe and Asia, please contact for details. Items with Free shipping applies only to Buy-it-Now option only. If "best offer" is accepted shipping charges will apply.
Payment Options Trail Werks Online accepts PayPal Only!
Returns 14 Day return policy. Returns are only accepted on un-opened merchandise in the original box and packaging. Roof racks and rack accessories are non-returnable items. Returns will only be accepted with a valid RA#. Returns may be subject to a 15% restocking fee. Buyer is responsible for all shipping charges on returned items. Buyer is responsible for verifying that product being purchased is the correct item. Please us if you have any questions.
Sign In
